Adding A Belt Hole

Think I would like to take it to someone who is experienced in doing it because the belt wasn't precisely low-cost and don't need to break it. Observe on the very end (that you will cut off later) to get a really feel for a way the drill and Leather interact. Looks like the Tandy Leather website retailer has gone kaput, the belt clean and belt hold links don't work any longer. Tom, Unfortunately it looks like this revealed across the similar time Tandy did a value increase on the belt clean. Tom: $7 balm + $1 keep + $2 buckle + $19 belt clean = $29 - $10 from code = $19. I have already got Sno Seal at residence and wish to keep away from purchasing the Leather Balm if it does the same thing.
Work the Leather up and down the opening to attempt to stretch it out a little bit because it won't be the exact same size as the opposite holes that had been punched initially. Next we need to get rid of the surplus Leather on the end so we don't appear to be we have now a tail hanging out on the entrance of our pants. Once more I marked the place I felt appropriate with a sharpie and simply used my family scissors to chop the Leather. Ensure that it is trimmed and nice, after which high-stitch it in the identical way that you just did your belt piece.



Work slowly and carefully-this prime sew will maintain your belt together, but it will additionally look fantastically decorated if it's executed effectively! Start on the underside nook of the tail end (the place you possibly can see I left the threads on the left side), go down the end, after which pivot at the nook to show and proceed all the way down the size of your belt. It should not take a lot thread, but be extra careful if you're working with a thicker fabric.
If the new spot isn't precisely on a measured place, create a Hole barely past that time. After checking the dots yet another time for accuracy, place the belt within the Leather punch instrument. Lining up the reducing level and the hole, clamp down on the tool as arduous as doable to punch the opening. After cutting the holes, brush off the surplus Leather and check out the belt on for size. Make sure that the holes are giant enough that the buckle prong can match via utterly. Safe the belt to the table and place something beneath the belt first to guard the end.

This DIY is applicable for every type of fabrics or supplies used for making belts, so whether or not you utilize a Leather materials like I did and even something like canvas or cotton, this tutorial will be good for you! Buckles range in all completely different sizes, styles, and widths, and whatever buckle you utilize will be essential to deciding what measurement your belt can be. The buckle I used is the bronze one within the image above, so any measurements I talk about specifically are designed for that one.
My dad taught me a fantastic trick when using an axe to make a new Hole: Rigorously maintain the metallic tip in an open stove flame for a minute or two, then fastidiously push it by means of the Leather. It can seal the hole to the proper dimension and keep it from shrinking up. By the best way, I am girl (yeah, hear me roar). I just lately bought an archery quiver, and even on the shortest setting, the Leather straps are still way too long. After the drill bit penetrates the belt, transfer the drill up and all the way down to filter the chaff from the perimeters of the hole.
It should come with snaps to carry the buckle on, so all we'll must do is trim the tip to measurement, match it for a Hole, and protect the Leather. Leather Balm with Atom Wax in Impartial, $6.ninety nine The Leather that you simply're shopping for is untreated. If you'd like a colored belt as an alternative of the pure shade, you can change this with water primarily based Leather dye. You should utilize a Leather punch to create the belt Hole, or if you don't have one, you'll be able to rigorously use an influence drill.

After a couple of minutes I was able to make a Hole large enough for me to power the belt buckle to undergo nevertheless it looked really crappy and a bit embarrassing to wear in public. Take a sheet of paper and fold it in half and put it behind the belt (or whatever Leather you are making an attempt to punch a hole hole puncher by way of) and THEN you punch it. Bam, excellent holes. But then again, if you happen to just need an extra Hole in your belt and you don't really care how good it punches holes, this is nonetheless a great product.
Take a tape measure and determine the width of your hips, or wherever your belt will be sitting once you put on it. Whatever quantity you provide you with, add about 8-10″ in. This ought to be the length of the fabric in your belt altogether! This cloth has a backing and is thick sufficient with only one layer, so I only wanted to cut one piece for the belt. With this Leather fabric, I needed to trim the perimeters so the perimeters lined up nicely with the squares of the basketwoven strips. You also needs to take the time to double-test that your strip of cloth on your belt will fit now that it is trimmed down.

Leave a Reply

Your email address will not be published. Required fields are marked *